ADSS光缆的力学计算

介绍了ADSS光缆的力学计算，给出了光缆弧垂、张力、应变和悬长等计算公式，并对普遍采用的“悬链线”和“抛物线”两种计算方法加以比较。     

工频电场对ADSS光缆特性的影响

随着电压等级的不断提高,超高压输电线路发展非常迅速.但是这些架空输电线路在运行时,附近存在较高的电场,对周围物体和公用走廊的其它线路会产生影响.电压等级越高,产生的电场影响越大.输电线路产生的电场越来越受到人们的重视.尤其是对于超高压输电线路,由于在电力铁塔上同塔悬挂全介质自承式光缆(ADSS),因此分析工频电场对ADSS光缆特性的影响非常必要.     

光总线在组合导航系统中的应用分析

航空电子系统和光通信发展到一定阶段，光总线将广泛应用于航空领域。在组合导航系统中，利用光总线进行通信可以极大地提高系统整体性能。本文介绍了光总线技术的发展及研究现状，重点分析了1394总线，提出了基于1394光总线的综合导航系统的网络结构及关键技术。     

Development of cable fault location method using fiber optic distributed temperature sensor

When ground-fault problems occur on a cable line, immediate fault location and restoration are required. Therefore, various new methods to locate the fault point instantaneously have been investigated to replace such conventional methods as the Murray loop method and the pulse radar method [1]. These methods require a long time to locate the fault point. One possible fault location method is to sense the temperature rise following a ground fault using a fiber optic distributed temperature sensor. Application of this method was found feasible through sensing the temperature rise at a ground-fault test using a thermocouple as a temperature sensor with test cables [4]. A power/optical composite cable was prepared experimentally and after verifying its thermal mechanical performance, the temperature rise at an incidence of a fault was determined and the anticipated performance was demonstrated in a ground-fault test. This article describes the outline of the test.     

利用声光延迟线的距离欺骗干扰

距离欺骗干扰是雷达对抗的重要手段，延迟线是其关键技术。将声光延迟装置与固定光纤延迟相结合的混合延迟线，发挥了两者的优点，实现了较长的延迟时间以及延迟时间的连续可调。文中分析了其工作原理和性能指标，进行了延迟实验，论证了其可行性。     

Q195冷轧板材轧制困难原因分析

针对部分Q195冷轧板材存在轧制困难的现象，进行了现场检验与分析。带状组织、混晶现象严重导致变形强化系数偏高是造成轧制困难的主要原因。     

聚合物电解质PEO全固态电致变色窗

本文用聚合物ＰＥＯ的锂盐络合物作电解质制作全固态电致变色窗，讨论了器件的特性，以及工艺条件的影响。     

高Q Ba(Zn_(1/3)Ta_(2/3))O_3介质谐振器材料及其在毫米波系统中的应用

叙述了Ｂａ（Ｚｎ１／３Ｔａ２／３）Ｏ３介质谐振器材料的制备、结构、微波性能及典型应用。Ｂａ（Ｚｎ１／３Ｔａ２／３）Ｏ３介质材料介电常数εｒ为２９．５，频率温度系数τ≈０（－５５～＋８５℃），１０ＧＨｚ下最大无载Ｑ值１４７００，在２８ＧＨｚ测得Ｑ值约为４８００。这种材料具有高Ｑ值，特别适用于Ｘ以上波段作为振荡器电路中频率稳定元件。用这种介质谐振器已研制出８ｍｍ介质稳频微带耿氏振荡器，频率稳定度小于１０×１０－６／℃，最大输出功率达１８０ｍＷ。     

Interaction between bubbles and fibre optic probes in a bubble column

Spherical bulb fibre optic probes, developed and applied for bubble characterization in a bubble column and a slurry bubble column at high temperature, were investigated. The principle of operation of these new optical fibre probes is based on the difference in refractive indices between the gas and the liquid phases. The interaction between the gas bubbles and the fibre optic probes in a bubble column was studied using photographic techniques. The first objective of these experiments was to study the response of the sensors upon contact with gas bubbles of various sizes. The second objective of this study was to establish, under controlled situations, the optical probe bubble detection performance and ability for local quantitative measurements of the bubble rise velocity and the gas hold-up.